TECHNICAL DESCRIPTION :
Used For Density Tests on Aggregates as per Procedure Laid Down.Made of Brass/GI with Stainless steel Wire Mesh 6.3mm/4.75mm size6.3mm/4.75mm Ruggedly Constructed, Approximately 20cm dia x 20cm high.Complete with Handle
DIMENSIONS AND WEIGHT :
Size :0.3 m.(L)x 0.3 m(W) X 0.4m ( H )
Weight :Approx. 2 Kg
SERVICE REQUIRED :
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 05-DENSITY BASKET
TECHNICAL DESCRIPTION :
This Set is used For Specific Gravity And Water Absorption Of Aggregates.
The outfit comprises of
1. Electronic balance, capacity 5 kg. Least Count 0.1gm, provision is made in this balance to suspend density basket under material pan. This balance is mounted on an angle iron frame stand.
2. Density basket.
3. Air tight container to suspend density basket.
4. GI Tray of area not less than 650 cm sq.
5. Absorbent cloths 75cm x 45cm
DIMENSIONS AND WEIGHT :
Size :0.6 m.(L)x 0.6 m(W) X 1.0m ( H ) Weight :Approx. 40 Kg
SERVICE REQUIRED :
Power Supply : 230 v AC , Single Phase 6amps , 50 hz
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 06-SPECIFIC GRAVITY AND WATER ABSORPTION OF AGGREGATE
TECHNICAL DESCRIPTION : Used for sampling Aggregates, Ores, Refractory. It consists of a sheet metal box mounted on Legs and fitted with a series of chutes of equal width which discharge the material alternatively in Opposite Directions into separate pans. The chutes of the Riffle are steep enough to allow rapid flowing of the Materials. The instrument has 14 Nos. Chutes of 13mm width and is complete with receivers DIMENSIONS AND WEIGHT : Size :0.6 m.(L)x 0.6 m(W) X 1.0m ( H ) Weight :Approx. 20 Kg SERVICE REQUIRED : SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 07-RIFFLE SAMPLE DIVIDER
TECHNICAL DESCRIPTION : Designed for the reduction of test samples which are too large in volume to be conveniently handled. It handles any material from Sand sizes up to dia. 108 mm. Each Chute bar is 12 mm wide so that openings of 12-24-36-4848-60-72-84-96-108 mm are possible. Complete with two collecting pans. Clam shell hopper: 30 litres capacity. Very sturdily constructed, it is totally Cadmium Plated for rust Protection DIMENSIONS AND WEIGHT: Size: 0.6 m.(L)x 0.6 m(W) X 1.0m ( H ) Weight : Approx. 30 Kg SERVICE REQUIRED: SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 08-AGGREGATE SAMPLE SPLITTER
TECHNICAL DESCRIPTION : For Measuring of Resistance of Aggregate to Crushing. Consists of M.S. Cylindrical Container 150mm +/ 0.5mm dia. x 130mm to 140mm high with base plate 200 to 230mm/sqr x 6mm thick. A plunger of 148mm +/-0.5mm dia. x 100 to 115mm high. Supplied complete with Tamping Rod, 16mm dia. x 600mm long, both end rounded, 1 no. Metal Measure 115+/ 0.5mm dia. x 180 +/- 0.5mm115+/- high. DIMENSIONS AND WEIGHT : Size :0.3 m.(L)x 0.3 m(W) X 0.2m ( H ) Weight :Approx. 10 Kg SERVICE REQUIRED : SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 09-AGGREGATE CRUSHING VALUE APPARATUS
TECHNICAL DESCRIPTION :
For Determining The aggregate Impact Value.
The instrument consists of a circular base with Two vertical guides. The Hammer of weight 13.75 +/+/-0.25kg can be raised to fall freely down the vertical guides. The Height of fall can be adjusted through 380 +/ 5mm. The+/- Hammer is provided with a locking arrangement. The hammer falls freely to the base and is removable for employing. Supplied complete with metal measure 75mm dia. x 50mm high (For specimen preparation) and Tamping Rod 230mm long x 10mm diameter.
A Blow Counter to count the number of strokes is fitted on top of the equipment
DIMENSIONS AND WEIGHT :
Size :0.3 m.(L)x 0.3 m(W) X 0.5m ( H )
Weight :Approx. 10 Kg
SERVICE REQUIRED :
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:-10-AGGREGATE IMPACT TESTER
TECHNICAL DESCRIPTION :
Used for testing Crushed Rock, Crushed Slag, Crushed and Uncrushed Gravel For Resistance to Abrasion.
The machine consists of a hollow cylinder mounted horizontally on a study frame on ball bearings. There is an opening which can be closed with a dust tight cover to facilitate charging and discharging the drum with the material under test. A detachable shelf which extends throughout the inside length of the drum which catches the abrasive charge and does not allow it to fall on the cover. The drum is rotated by an electric motor through a heavy reduction gear at a speed of 30-30 33 R.P.M. A revolution counter is fitted to the frame. A tray is supplied for collection of the material at the end of the test. Complete with. Abrasive Charge consisting of a set of Twelve hardened steel balls, approximately 48mm dia. Suitable for operation on 440 V, 3 Phase, 50 cycles, A.C. Supply.
DIMENSIONS AND WEIGHT :
Size :1.0 m.(L)x 1.0 m(W) X 1.0m ( H )
Weight :Approx. 90 Kg
SERVICE REQUIRED :
Power Supply : 440 v AC , Three Phase 15 amps , 50 hz
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 11-LOS ANGELES ABRASION TESTING MACHINE
TECHNICAL DESCRIPTION :
For Testing Aggregates for Resistance to Abrasion.
It consists of a disc rotating about a shaft connected to a reduction gear box coupled to a motor. The disc rotates at 28 30 RPM. Under28-30 the rotating disc is a tray with an outlet to facilitate the removal of sand. Two Conical Hoppers are mounted on a bracket fixed to the circular tray. An arrangement is made for start and stop the flow of sand. Two containers with weights are supplied to keep the specimens pressed against the rotating disc. Suitable for operation on 220 V, 50 cycles, A.C. Supply
DIMENSIONS AND WEIGHT :
Size : 1.0 m.(L)x 1.0 m(W) X 1.0m ( H ) Weight : Approx. 90 Kg
SERVICE REQUIRED :
Power Supply : 230 v AC , Single Phase 15 amps , 50 hz
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 12-DORRY ABRASION TESTING MACHINE
TECHNICAL DESCRIPTION :
For The Determination of Resistance of Aggregates to Wear by Abrasion.
It consists of two hollow cylinders closed at one end and provided with Fitting covers at the either end. These cylinders are mounted an a shaft 0 at angle of 30 with the axis of rotation of the shaft. The shaft rotates at 30-33 RPM. Through a reduction gear operated by a motor and is provided with a revolution counter. Complete with Abrasive Charge consisting of 12 Nos. Hardened steel Balls of 48mm dia. Suitable for operation on 440 Volts, Three Phase, 50 Cycles, A.C. supply.
DIMENSIONS AND WEIGHT :
Size :1.0 m.(L)x 1.0 m(W) X 1.0m ( H )
Weight :Approx. 50 Kg
SERVICE REQUIRED :
Power Supply : 230 v AC , Single Phase 15 amps , 50 hz
SCOPE OF DELIVERY:
1. Experimental Setup
2. Instructional Manual
Get PDF:- 13-DEVEL ATTRITION TESTER
TECHNICAL DESCRIPTION :
This is used for determination of resistance to wear for Cement & Concrete flooring tiles. Tiles specimen of size 7.06 cm x 7.06 cm is pressed face-wise under specific load on a grinding path and abrasive powder is evenly spread on the rotating grinding disc the second parallel side of the tile is subjected to wear for similar number of rotations. The wear of the tile is measured on a thickness gauge specifically made for the purpose. The machine consists of a disc rotating at a speed of 30 R.P.M. in a circular tray. A bracket is provided to hold the specimen. A counter balance lever loads the specimen. Load applied is 30 Kgf. A funnel is fitted to evenly spread abrasive powder on the grinding path. A Pre set Counter automatically stops the machine after 22 revolutions. This counter is Re-adjustable. The machine works on 440 V A.C. Three Phase electrical supply. On Request machine to operate on 230 V A.C. Supply can also be supplied
Get PDF:- 14-TILE ABRASION TESTING MACHINE
